|
Quick
Resources: PDF
Brochures -- Product Guides
Installation
Kits
Access
Bank I Access
Bank II Access
Bank II/SDSL Access
Exchange
SpeedwayTM Installation
Kit (for Access Bank or Access Exchange units)
Your installation is literally a snap. This Kit uses locking tabs and
pins, versus screws, to install up to two Access Bank or Access
Exchange units. Customer installation tests have shown up to a 75%
reduction in installation time, as well as up to a 45% smaller
footprint.
Cables
Access
Bank I
TR-08 Conversion Cable
TR-08 Conversion Cable for DS-0 to analog
interface channel reassignment in reference to Bellcore TR-08
specifications for Mode I operation, providing the standard wiring
sequence for Tip and Ring pairs. The cable is ten feet long with one
50-pin Amphenol female connector on the Access Bank I end, and one
50-pin Amphenol Telco connector on the punchdown block end. This cable
is optional for TR-08 operation on the Access Bank I.
Access
Bank II
E&M Normal Cable
4-Wire E&M Normal Mode cable for
use with each 12 channel analog card. The cable is ten feet
long with a 96-pin DIN female connector on the Access Bank II end, and
two 50-pin Amphenol Telco connectors on the punchdown block end.
Normal mode operation is typical for attachment to switching
equipment, such as PBX systems.
E&M Tandem Cable
4-Wire E&M Tandem Mode cable for
use with each 12 channel analog card. The cable is ten feet
long with a 96-pin DIN female connector on the Access Bank II end, and
two 50-pin Amphenol Telco connectors on the punchdown block end.
Tandem mode operation is typical for attachment to other transmission
equipment, such as microwave or public 4-Wire E&M lines. Alternate
names for Tandem operation are Reverse E&M or Pulse Link Repeater
(PLR).
E&M Transmission Only (TO) Cable
Transmission Only (TO) Mode cable for
use with each 12 channel analog card. The cable is ten feet
long with a 96-pin DIN female connector on the Access Bank II end, and
one 50-pin Amphenol Telco connector on the punchdown block end. TO
mode operation is typical of dedicated "transmit only"
operations, such as leased-line modems and radio equipment.
RS-232 Dual Cable
Dual RS-232 User Data and Management
Cable for connection to a router, computer, statistical multiplexer,
SNA controller, SCADA equipment or other data equipment. The cable is
ten feet long with one fine pitch D-Sub-26 male connector on the
Access Bank II end, and two DCE DB-25 female connectors on the data
equipment end. The Access Bank II supports both synchronous operation
at 56 or 64Kbps, and asynchronous operation at 1.2, 2.4, 4.8, 9.6,
14.4, 19.2, 28.8, 38.4, and 57.6Kbps. The RS-232 User Data and
Management Cable is required for RS-232 data operation on the Access
Bank II.
Access
Bank II & Access Exchange
V.35 Male Cable
V.35 Data Cable (male connector) for
connecting a router (with female V.35 connector) or other data
equipment to a T1 network using the Access Bank II's V.35 Data Port.
The cable is ten feet long with one fine pitch D-Sub-26 male connector
on the Access Bank II end, and one DCE V.35 Winchester male connector
on the digital device end. The V.35 Data Cable is required for V.35
data operation on the Access Bank II.
V.35 Female Cable
V.35 Data Cable (female connector) for
connecting a router (with male V.35 connector) or other data equipment
to a T1 network using the Access Bank II's V.35 Data Port. The cable
is ten feet long with one fine pitch D-Sub-26 male connector on the
Access Bank II end, and one DCE V.35 Winchester female connector on
the digital device end. The V.35 Data Cable is required for V.35
data operation on the Access Bank II.
BRACKETS
Please note: You must order a pair of
heavy-duty Rack Brackets for each Access Bank product installed. For
all vertical mounts, please order a pair of the respective Vertical
Mount Brackets.
19" Rack Bracket Pair
(P/N 710-0041)
Two (2) heavy-duty 19" rack mounting
bracket allows installation in equipment racks and cabinets with
variable front to back offset. This bracket can be used with Carrier
Access' Access Bank family.
23" Rack Bracket
Pair (P/N 710-0130)
Two (2) heavy-duty 23" rack mounting
bracket allows installation in equipment racks and cabinets with
variable front to back offset. This bracket can be used with Carrier
Access' Access Bank family.
19" Vertical Mount Bracket
Pair (P/N 710-0115)
Two (2) heavy-duty 19" horizontal
cross bars for vertical installation in equipment racks and cabinets.
This bracket can be used with Carrier Access' Access Bank family.
23" Vertical Mount Bracket
Pair (P/N 710-0117)
Two (2) heavy-duty 23" horizontal
cross bars for vertical installation in equipment racks and cabinets.
This bracket can be used with Carrier Access' Access Bank family.
Wall Mount Bracket
Wall mounting bracket set (4 pieces) for
wall mount installation. This bracket can be used with Carrier Access'
Access Bank family included with each order.
|
E-Mail
Related