|
Processor |
Supports Intel FC-PGA2
Pentium 4 processor in the 478 pin package
Supports 1.3 ~ 2GHz and Higher
400M Hz FSB (standard) and support multi FSB setting from BIOS
CPU frequency adjusting from BIOS |
|
Chipset |
North :
Intel 845 (593 FC-BGA) MCH HubA HOST/AGP/Controller
• Support a single processor with a data transfer rate of 400M HZ
• Support DDR 200/266 operation
• AGTL+ host bus with integrated termination support 32-bit host addressing
• 1.5V AGP interface with 4X data transfer and 4X fast write capability
• 8-bit,66MHz 4X hub interface to the ICH2
South : Intel 82801BA ICH2 (360 EBGA) I/O Controller Hub
• Upstream hub interface for access to the Intel MCH
• 2-channel Ultra ATA/100 Bus Master IDE controller
• Build in RTC² USB controller 1.1
• I/O APIC² SMBus controller
• FWH interface² LPC interface for SIO
• AC'97 interface² PCI 2.2 interface
• Integrated LAN controller |
|
Memory |
Supports
four memory banks using two 184-pin DDR DIMM
Support DDR 200/266 compliant un-buffer / ECC SDRAM up to 2GB capacity
Supports 2.5V DDR SDRAM |
|
I/O
Controller |
Winbond
83627SF Super I/O chip
• Comply with Intel Low Pin Count Interface Specification Rev. 1.01
• Built in H/W monitor feature
• Support LDRQ#(LPC DMA) , SERIRQ(serial IRQ)
• Support DPM (Device Power Management) , ACPI
• Keyboard Controller
• Floppy Disk Controller Supports two 360K/ 720K/ 1.2M/ 1.44M/ 2.88M floppy
disk drives
• Two 16C450 UARTs support standard serial Ports ² Supports IrDA 1.0SIR/ASKIR
protocols |
|
One IEEE
1284 Parallel Port support SPP/ECP/EPP mode LAN |
Realtek
RTL8100 10/100 Mb controller ( Optional ) |
|
On-Board
IDE |
An IDE
controller on the Intel 82801BA (ICH2) chipset provides IDE HDD/CD-ROM with
PIO,
Bus Master and Ultra DMA33/66/100 operation modes.
Support up to four IDE devices.
ATAPI IDE CD-ROM, CD-R, CD-RW, and LS-120 Supports |
|
On-Board
Peripherals |
1 floppy
port supports 2 FDDs with 360K, 720K, 1.2M, 1.44M and 2.88Mbytes
2 serial ports
1 parallel port supports SPP/EPP/ECP mode
2 USB ports
1 IrDA connector for IR |
|
PLC To
ISA Bridge |
Winbond
W83628 + W83629 Meet LPC Spec. 1.1 |
|
Slots |
1 x AGP
(Accelerated Graphics Port) slot support 4x mode (1.5V only) NOTE : The AGP
slot DOES NOT support 3.3V AGP 2x card. Use of 3.3V AGP 2x card may cause
damages to the mainboard.
6 x PCI 2.2 32-bit PCI bus Master slots (support 3.3v/5v PCI bus interface)
1 x ISA slot |
|
Power
Management |
APM 1.2
compliant
ACPI 1.0 compliant
Supports Voltage monitoring
Supports temperature sensor
Suspend To RAM (STR) |
|
BIOS |
Award
BIOS with Flash ROM in Firmware Hub (FWH)
Supports Plug and Play 1.0A, AMP 1.2, Multi Boot, DMI
Full support for ACPI revision 1.0A specification
CPU 100 / 133MHz FSB setting
CPU core voltage setting from +0.025V ~ +0.20V
AGP (Vddq) voltage setting from +0.05V ~ +0.20V
I/O voltage setting from +0.1V ~0.2V
Bootable from IDE,Floppy, ATAPI device, USB device, LS120 , ZIP, SCSI device |
|
Board
Size |
Baby AT
Form Factor: 13" L x 8.66" W (330 mm(L) x 220 mm(W)) |
