ICP Electronics
ITouch Partner
Lucent Partner
Marconi Partner
Nortel Partner
RAD Partner
Telco Partner
Tellabs Partner
VoxTechnologies 3Com Partner
Adtran Partner
Alcatel Partner
CA Partner
ChannelBank
Eastern Partner
Enterasys Partner
Extreme Partner
Larscom Partner Kentrox Partner

	Input: Output Rating: (at 50oC) Note:The total output continuous power shall be kept under 140W at 24VDC input (ACE818C) The total output continuous power shall be kept under 100W at 12VDC input and forced air-cooling. Without fan cooling is only 80W.(ACE810V) TB-3 Connector Application explain PIN1: Power Good PIN2: Pulse signal indication of DC input status PIN3: +5Vsb PIN4: Ground PIN5: Power on PIN7/PIN8: Measure battery capacity *Notes: It can be used as an identifier by PIN2 signal while there are interrupt of DC power and recovery. For ACE810V/818C are not only applied as a power supply. It can be tread as a UPS (uninterruptible power supply) while combined with battery module .This series of power supply provide stable of electronic and send signal from TB-3 of PIN2 for doing system control and configuration dependence on user's demands. Moreover, it is easy to connect within voltameter for doing voltage monitoring.

• Min. Load: +5V/0.5A +12V/0.2A
• Efficiency: Higher than 70% at 12V or 24VDC input
• Protection: over voltage, short circuit, and over load protection.
• Input polarity operation: When wrong polarity is connected to input terminal, should not cause any damage on the power supply.
• Power On Signal: This TTL compatible signal (active low) is use to switch ON the main output. When ¡§Power ON¡¨ is disconnected from secondary common, all outputs except +5Vsb shall turn off.
• Battery Backup and Hold up time: Upon loss of DC input, the unit must operate from the battery. Hold up time is around 2 minute on the battery capacity.
• Built-in cooling fan
• MTBF: 110,000 hrs
• Vibration: 10Hz~55Hz at 2G, 3minutes period, 30 minutes along X, Y, and Z axis.
• Shock : 10G for 11ms half sine wave, one time for each of ¡ÓX, ¡ÓY , ¡ÓZ axis.
• Safety: Designed to meet the following standards UL 60950 CSA 22.2 No.60950 EN 60950: 2000
• EMI : Designed to meet the following radiation limited : FCC docket 20780 curve "B" EN55022 class "B"
• EMS : Designed to meet the following limits EN61000-4-2 4KV contact; 8KV air discharge Criterion B
  EN61000-4-3 10V/M with 80% AM Criterion A
  EN61000-4-4 2KV Criterion B
  EN61000-4-5 0.5KV Criterion B
• Operating Temp. : 0~50ºC
• Storage Temp.: -20 ~85ºC
• Connectors :
  TB1- primary DC input: 3-position Terminal blocks
  TB2-DC output: 6-position Terminal blocks
  TB3-auxiliary 8-pin connector:
  
  When Vin Signal 1 change state, Vin signal 2 will Provide one shot pulse between 0.2 sec and 0.6 sec

• ACE818C : +24V DC Input 140W ATX / Battery Backup Function Power Supply

• ACE810V : +12V DC Input 100W ATX / Battery Backup Function Power Supply

An Industrial Partner 1999-2002. All rights reserved.

Industrial Products Home

E-Mail

VoxTechnologies Corp. - Industrial Computer Leader Tel: 1-972-234-4343 Fax: 1-972-234-4295 Toll-Free: 1-888-568-6224

For over a decade, VoxTechnologies has been a leading source of industrial computers and complete system products for the O.E.M. and Systems Integrator. Our primary goal is to provide a solution source for engineers that have the challenging task of interfacing and controlling the real world.

Telephone: 972-234-4343 General Info: info@voxtechnologies.com Sales Info: sales@voxtechnologies.com